The MasterFrame 600 is much from an oversize tower, however every part from the cast-aluminum corners to the assist for triple-fan 360mm-format radiators speaks of Cooler Grasp’s need to impress. The radii of these corners present the molded-together look that Cooler Grasp had previously achieved utilizing plastic faceplate bits, with the brand new design decreasing using plastic to issues like the facility button and the cable insulation. Even the air flow holes within the entrance face are a bit “additional”: They’re formed like Cooler Grasp logos.
(Credit score: Thomas Soderstrom)
The plastic energy and reset buttons are unlit; the MasterFrame 600’s sole indicator LED shines its power-on sign by a gap within the aluminum panel. Twin USB 3.x Sort-A ports, a Sort-C port, and a headphone/mic (headset) combo jack full a detachable part that, within the factory-installed configuration, is situated on the ahead finish of the highest panel.
Round again, we discover the one exterior panels on this case which are product of metal, fairly than aluminum. These embrace an higher rear panel with the motherboard I/O plate and a factory-filled 120mm fan mount, the middle part with an eight-slot PCI Specific growth card panel, and the decrease part, with its power-supply mounting plate. These panels are detachable, however solely for the aim of swapping the facility provide’s place from the underside of the case to the highest. We see no provisions for turning the PCIe card slot holder sideways.
(Credit score: Thomas Soderstrom)
Magnets on the high and catch tabs on the backside allow tool-free entry to the MasterFrame 600’s inside. Inside, a set of horizontal crossbars secures the motherboard tray and different inside panels to the outer body. The 2 vertical bars may be spaced to mount both a set of aspect followers or 3.5-inch exhausting drives.
(Credit score: Thomas Soderstrom)
Sheet-steel frames on the within of the MasterFrame 600’s aluminum face, high, and right-side panels present the fabric for the body’s screwed-on magnets to draw. Mud filters are tucked between the outer aluminum and internal metal body of the highest and entrance panels, whereas plastic snaps maintain the correct panel’s filter on to its aluminum sheet utilizing welded-on studs.
The underside panel’s mud filter is less complicated to take away. For the reason that underside is metal, its filter is caught in place utilizing magnetic strips.
(Credit score: Thomas Soderstrom)
From its cross bars, the MasterFrame 600’s motherboard tray is offset round 1.3 inches, its cable cowl round 2 inches, and its triple 2.5-inch drive tray round 0.8 inch. All of those items reside behind a trio of factory-installed 140mm consumption followers.
(Credit score: Thomas Soderstrom)
We talked about the varied distances at which the inside panels stand to emphasise that they’re not on the identical aircraft. (The cable cowl, for instance, stands out previous the board, because it’s supposed to cover sure cables.) And whereas all of those panels are detachable, none supplies the additional mechanical assist to sturdily mount a 13-inch-deep EATX board. Eradicating the cable cowl will, nonetheless, give builders sufficient room to put in the 9.6-to-10.7-inch enthusiast-class motherboards that additionally carry the EATX label. We eliminated simply one of many panels under at proper to point out the place the side-fan mount resides.
(Credit score: Thomas Soderstrom)
Need extra metal? The ability provide’s shroud, its detachable endcap, and the perforated metal backside panel all qualify. By now, you’re in all probability noticing the continual sequence of mounting holes across the fringe of the case that permit most of those elements to be repositioned.
(Credit score: Thomas Soderstrom)
Even the port panel may be relocated from the entrance of the highest panel to the underside of the entrance panel. On condition that it shares a part of the case’s high with an adjoining panel, shifting the port module to the entrance additionally requires shifting the highest panel to the entrance; the displaced entrance panel then strikes to the highest.
Get Our Greatest Tales!
All of the Newest Tech, Examined by Our Consultants
By clicking Signal Me Up, you affirm you’re 16+ and conform to our Phrases of Use and Privateness Coverage.
Thanks for signing up!
Your subscription has been confirmed. Regulate your inbox!
The massive factor, although, that offers this case some future spark is the choice to vary out entrance and high panels altogether for new-look ones. Cooler Grasp has mooted elements with pale and darkish wooden finishes, and many else. For now, the Cooler Grasp website affords solely a Case Panel Pure (in eucalyptus wooden), in addition to an particularly intriguing Case Panel Stone (with a stone-like floor). Each will match the highest or entrance sections of the MasterFrame 600 case. We could not discover them really out there anyplace but, although, and we’re unsure if this would be the extent of the optionally available bits Cooler Grasp will provide.
Cables embrace HD Audio, a nine-pin energy/reset button/LED front-panel combo connector, a dual-link Gen 2 (that’s, Gen 2×2) cable with a Sort-E motherboard connector and a Sort-C port, and a 19-pin USB 3.x connector with two Sort-A ports.
(Credit score: Thomas Soderstrom)
Eradicating the port unit (above) provides us a greater perspective (under) on how related the holes are for the entrance and high panels: They’re equivalent. Each have magnets screwed to 1 finish for attaching the corresponding entrance or high panel, and each are full of a multi-spaced bracket for putting in 120mm to 200mm followers. Right here’s the catch: The house taken up by ports and buttons reduces the house out there for adjoining followers from three 140mm followers to a few 120mm ones.
(Credit score: Thomas Soderstrom)
